Gentec-eo MACH 6 Manuel d'utilisateur

Mach 6 User’s Manual Revision 2.1 1

Mach 6 User’s Manual Revision 2.1 10 Range LED. Should either of these conditions occur, co

Mach 6 User’s Manual Revision 2.1 11 Figure 3, Instrument Controls Display The main cont

Mach 6 User’s Manual Revision 2.1 12 Trigger Polarity Sets the trigger edge polarity for t

Mach 6 User’s Manual Revision 2.1 13 Read 2, pulse offset = 500,001, number of pulses to re

Mach 6 User’s Manual Revision 2.1 14 With internal triggering, if the pulse is below the t

Mach 6 User’s Manual Revision 2.1 15 1s 68.27% 2s 95.450% 3s 99.7300% 4s 99.

Mach 6 User’s Manual Revision 2.1 16 with wavelength, turning Wavelength Compensation on ma

Mach 6 User’s Manual Revision 2.1 17 Pulse Energy (in Joules), Time Stamp (in Seconds), Pr

Mach 6 User’s Manual Revision 2.1 18 Calls a display of measured data sampled at a 10Hz ra

Mach 6 User’s Manual Revision 2.1 19 The Life Test Display Run Life Test The Life Tests

Mach 6 User’s Manual Revision 2.1 2 WARRANTY The Gentec-EO MACH 6 Meter carries a one-year

Mach 6 User’s Manual Revision 2.1 20 The Controls are: Start Test Starts the test with

Mach 6 User’s Manual Revision 2.1 21 The Number of pulses to measure when the instrument i

Mach 6 User’s Manual Revision 2.1 22 The selected stats will be stored, comma separated.

Mach 6 User’s Manual Revision 2.1 23 The current status of the running test sequence. Dat

Mach 6 User’s Manual Revision 2.1 24 Recalls a saved instrument setup. Statistics Colors

Mach 6 User’s Manual Revision 2.1 25 initializes the GUI and the instrument based on the in

Mach 6 User’s Manual Revision 2.1 26 Figure 4, Strip Chart Display The functions of the

Mach 6 User’s Manual Revision 2.1 27 Places a cursor on the minimum value and its time sta

Mach 6 User’s Manual Revision 2.1 28 Min The minimum pulse energy in the data set. Max

Mach 6 User’s Manual Revision 2.1 29 Figure 5, Histogram Display The functions of the co

Mach 6 User’s Manual Revision 2.1 3 SAFETY INFORMATION Do not use the MACH 6 if the device

Mach 6 User’s Manual Revision 2.1 30 Figure 6, Statistics Display The functions of the c

Mach 6 User’s Manual Revision 2.1 31 The maximum pulse energy in the data set. Mean The

Mach 6 User’s Manual Revision 2.1 32 the mode of X is 4 because that is the value that most

Mach 6 User’s Manual Revision 2.1 33 Figure 7, FFT Display The function of the controls

Mach 6 User’s Manual Revision 2.1 34 Figure 8, Probe Data Display The functions of the c

Mach 6 User’s Manual Revision 2.1 35 Log Wavelength Scale Toggles the wavelength axis of

Mach 6 User’s Manual Revision 2.1 36 The Controls are: Measured Average Power Enter th

Mach 6 User’s Manual Revision 2.1 37 After the probe EPROM is written, Mach 6 will be rese

Mach 6 User’s Manual Revision 2.1 38 Getting Ready to Measure Data The Mach 6 instrument

Mach 6 User’s Manual Revision 2.1 39 a trigger is generated by the instrument. For external

Mach 6 User’s Manual Revision 2.1 4 Contents Introduction ...

Mach 6 User’s Manual Revision 2.1 40 Note that when the instrument is set back to internal

Mach 6 User’s Manual Revision 2.1 41 tracking had been turned on, the trigger level would h

Mach 6 User’s Manual Revision 2.1 42 minutes of data. Pressing the ARM button again stops d

Mach 6 User’s Manual Revision 2.1 43 Missing Pulses The Mach 6 Applications software is

Mach 6 User’s Manual Revision 2.1 44 The response of the probe is stored in the probe memor

Mach 6 User’s Manual Revision 2.1 45 Instrument Specifications Power Sup

Mach 6 User’s Manual Revision 2.1 46 Recycling and separation procedure. This section is

Mach 6 User’s Manual Revision 2.1 47 DECLARATION OF CONFORMITY Application of Council Dir

Mach 6 User’s Manual Revision 2.1 48

Mach 6 User’s Manual Revision 2.1 5 7.8.2 Dismantling procedure: ...

Mach 6 User’s Manual Revision 2.1 6 Figure 2, Mach 6 Back Panel Installing the Software

Mach 6 User’s Manual Revision 2.1 7 6. Leave the CD in your PC as the USB drivers are loca

Mach 6 User’s Manual Revision 2.1 8 The software installation is now complete. You may no

Mach 6 User’s Manual Revision 2.1 9 The Armed LED illuminated when the unit has been armed